Location : Vadodara
Carbo Cashew CNSL Resin Mortar is widely used for Acid Resistant Bricks / Tiles lining as bedding and jointing mortar.
It can be used for jointing Chemical Resistant Stoneware Pipes. It is also used for ETP Plants. It is suitable where excellent resistant property and heavy impacts subjected to the surface of floors and tank is required. Carbo Cashew Cnsl mortar adheres strongly on the Ceramic, Concrete surface and metals so, it can be used as a monolithic lining for the construction of dilute acids storage tanks.
It is resistant to Acids, Alkalies, mixed alkaline solutions with acids.
170° C (Max.)
Preparation of Mortar generally consists of Solution & Powder. In order to obtain good working consistency, the average mixing ratio is 1 Pbw of Solution & 2pbw of Powder. This ratio will slightly vary depending upon the temperature and working conditions.
Prepare small batches of Mortar. Stirrer the Solution thoroughly before use. Place the Solution in a suitable mixing pan and add powder in it. Mix thoroughly with a spatula or Trowel. The mixing operation shall be continued until a uniform mixture is obtained.
Make sure that all the Mortar is used from the mixing pan before another batch is prepared.
The cement plastered surface shall be slightly rough in line & level , dry & clean, free from dust, dirt, grease, oil etc., maintaining required slope etc. as no slope can be adjusted or altered in Acid proof lining works.
Carbo Cashew Cnsl Resin Mortar is a Self-hardening due to its chemical reaction which occurs when the Powder & Resin are mixed together.
Please ensure that no water shall be spilled over the bricks lining works before it completely cured.
All two components are stored in cool and dry place under the roof until ready to use it original unopened (Sealed) containers.
Location : Ahmedabad
3M Primer 94 promotes adhesion and increases bond strength. Primer 94 is used where priming is needed for hard-to-bond surfaces. Advantage of Primer 94 is that it can be used on wider range of surfaces. It promotes adhesion and increase bond strength on difficult to bond surfaces like propylene, polyurethane, powder coated paints, thermoplastic rubber and TPO. It dries quickly for fast tape application.
Location : Vadodara
Quick wood is a versatile hand knead able instant action epoxy putty of American origin, which mixes in just one minute for permanent repairs of cracked, torn, rotted, worn, scratched or damaged wooden parts having nails and screw holes, gouges or scratches.
Quick wood is available in 4 Oz 114 grams 7 inch long stick form containing curing agent encapsulated in concentric base material spread over entire length. One has simply to cut, knead and apply. There is nothing to weigh or measure. The application needs no training, no special tools or any equipment. It does not shrink or gets De-colourised when exposed to UV radiation. After proper kneading, quick wood looks like original wood and behaves like molding clay to repair, restore, recondition or rebuild anything made out of wood. The repaired portion can be smoothly finished by rubbing with wet cloth/water. After being cured, repaired portion becomes integral part of item being repaired. Quick wood upon curing has same color as well as density as wood.
Location : Vadodara
Location : Delhi
Devcon Titanium Putty
Features: Devcon Titanium Putty is Correctly formulated, Effectiveness, Accurately packed.
Devcon Titanium Putty Product Description: Devcon Titanium Putty is a high performance, titanium reinforced epoxy engineered for making critical repairs to machinery and precision parts
Devcon Titanium Putty's Features And Benefits:
Temperature resistance to 176 Degrees Centigrade
Excellent chemical resistance
Compression strength of 124 MPa
Qualifies under mil spec DOD-C-24176B
Non-rusting, machinable to metallic finish
Restore bearing housings and scored shafts
Rebuild wear rings, hydraulic rams and valves
Repair equipment and parts that require a machined finish
Devcon Titanium Putty's Typical Physical Properties : Cured 7 days @ 24
Mixed Viscosity : Putty
% Solids by Volume : 100
Cured Density : 2.36 gm/cc
Cured Shrinkage ASTM D2566 : 0.0010 cm/cm
Specific Volume : 422 cm3/kg
Pot life at 24oC (0.5kg mass) : 21 minutes
Compressive Strength ASTM D695 : 129.8 MPa
Adhesive Tensile Shear ASTM D1002 : 13.8 MPa
Cured Hardness Shore D ASTM D2240 : 87D
Dielectric Strength, volts/mm ASTM D149 : 2205
Coverage : 843 cm2 /kg 5mm
Devcon Titanium Putty's Temperature Resistance : Wet 66 Degrees Centigrade/ Dry 177 degrees centigrade
5% Bleach (Sodium Hypochlorite) - E , 10% Phosphoric Acid VG
5% Trisodium Phosphate - E , 10% Sulphuric Acid F
10% Sulphuric Acid - E , 10% Sodium Hydroxide E
50% Sulphuric Acid – E , 50% Sodium Hydroxide E
10% Hydrochloric Acid – E , 5% Alum (Aluminum Sulfate) E
0% Nitric Acid – U , 10% Acetic Acid - U
KEY : E = Excellent, VG=Very Good, F-Fair, Unsatisfactory
Devcon Titanium Putty are very good in water, saturated salt solution, leaded gasoline, mineral spirits, ASTM #3 Oil and propylene glycol. Epoxies are generally not recommended for long term exposure to concentrated acids and organic solvents.
Surface Preparation forDevcon Titanium Putty : Proper surface preparation is essential to a successful application.
Devcon Titanium Putty, Devcon Plastic Steel Putty, Devcon Epoxy Putty, Plastic Steel Putty, Devcon Epoxy, Maintenance repair and Overhaul, INDUSTRIAL EPOXY PUTTIES, 180 Degrees Centigrade, ON LINE LEAK ARRESTOR, DEVCON, EPOXY PUTTY, BRUSHABLE CERAMIC, TITANIUM PUTTY, STEEL PUTTY, HIGH TEMPERATURE, RESISTANT, PUTTY, BELZONA 1111, BELZONA BRUSHABLE CERAMIC, BELOZONA EPOXY PUTTY, WURTH SILICON SPRAY, Instant Adhesive, Anti Corrosive Coating, Metal Repair Putties, Cold welding Compound, Bronze Putty, Wet Surface Putty, Abrasion Resistant Putty, Under water Putty, Devcon Plastic Steel Putty, Devcon 5 Minutes Epoxy Putty, Devcon 5 Minute Epoxy Putty, Devcon Stainless Steel Putty, Devcon Metal Magic Bond, Devcon Aluminum Putty, Machinable Putty, Easily Drilled Putty, Online Leak Arrestor, High temperature resistant leak arrestor, Marine Grade Putties, Food Grade Epoxy Putty, Devcon Plastic Steel Putty (A), Devcon Plastic Steel 5 Min Putty (SF), Devcon Titanium Putty, Devcon Brushable Ceramic Blue / Red, Devcon Wet Surface Repair Putty (UW), Devcon Wet Surface Repair Putty (UW), Devcon Aluminium Putty (F), Devcon Bronze Putty (BR), Devcon Stainless Steel Putty (ST), Devcon Flexane 80, Aquafix, Aquafix Pipe repair kit, Transformer Oil leak Sealant, Online Oil Leak Sealant, Pipe Leak Sealant, Metal Repair, Metal rebuilding.
Location : Surat
Backed by a team of highly skilled and experienced professionals, we have been able to provide a quality assured Instant Adhesive that issued for fast bonding of plastic, glass, leather, metal, rubber and wood. Offered adhesive is processed at our ultra-modern processing unit using supreme grade chemical...
Location : Vadodara
Cutting and grinding, general abrasives, silicone and sealants, general adhesives, paints and coatings, waterproofing, putty and other consumables
Location : South Africa
The offered Water Resistant Adhesive is processed at our vendors’ well-cleaned processing unit with the help of latest technology under the most favorable condition using optimum grade chemicals. This adhesive is available in various specifications and can be availed in different packing options. It is tested on various quality parameters by our highly skilled quality analyst. Clients can avail this adhesive from us as per their needs at competitive prices.
Available in All types of Packing and Sizes Such As:
Location : Vadodara